3d printed M11/9 upper cap

[Gaujo]

I know the hits have been coming pretty fast on the 3D printed stuff but it's got me fired up! Check this doohickie out: it's a cap for an 11/9 upper to hold the bolt in for storage. I have dropped a CFW bolt on my foot and can vouch for the usefullness
https://odysee.com/@MiddletonMade:1/M11ZipLock:6

[mtlcafan79]

I have this queued up to print. I'm interested to see if it fits a Lage upper, or just a stock style upper. His other designs are supposed to fit Lage uppers so we shall see.

[Deerhurst]

Hmm. I might have to design one for the.M10! Would make storing spare upper easier.

[DistalRadius]

I use a rubber band.

[ScottinTexas]

There is commercially a very similar device used on an AR that keeps the bolt and charging handle from sliding out. I have a couple and these are worth every penny.

https://www.joeboboutfitters.com/pro...t-bolt-sav.htm

https://www.blackdogmachinellc.net/u...-uppers-1.aspx

I was using some giant rubber bands but they don't age well and when they get a few years on them they tend to disintegrate....and there goes your bolt, on the kitchen tile or wood floor.

[Gaujo]

Hmm. I might have to design one for the.M10! Would make storing spare upper easier.

How much should I shorten it for the m11a1?

[Gaujo]

There is commercially a very similar device used on an AR that keeps the bolt and charging handle from sliding out. I have a couple and these are worth every penny.

https://www.joeboboutfitters.com/pro...t-bolt-sav.htm

https://www.blackdogmachinellc.net/u...-uppers-1.aspx

I was using some giant rubber bands but they don't age well and when they get a few years on them they tend to disintegrate....and there goes your bolt, on the kitchen tile or wood floor.

That thing is pretty sleek. I think we could take some weight off the other one.

[Deerhurst]

How much should I shorten it for the m11a1?

Not sure. I have an M10. I'll have to go measure stuff.

[Suzuki1750]

I made a cap for my lage 9mm upper a while back

[Gaujo]

I made a cap for my lage 9mm upper a while back

Pics and do you want to share?

[Novagunner]

I use a sock. Lol.

[jt526]

Love the cap.

My contribution to this is a fake upper to keep my CW bolt nice and safe. I have several bolts that need homes. Printed on Prusa angled side down, made to fit prusa mk3s height. I'll probably do one for the lage 22lr kit as well.

STL:
https://www.thingiverse.com/thing:5177594

[Gaujo]

Lol did u print a retaining pin too!? Way to go JT!

[mtlcafan79]

Retaining ping comes with the lower piece. I noticed that these do not work on Lage uppers that have pic rails installed on the sides.

[Tinman45]

I use a rubber band.

My rubber band got old and less snappy. Now I use a fat zip tie.

[SecondAmend]

Velcro band

[jt526]

I’ve got 2 of the caps that don’t meet my standard (the bottom bridge didn’t have the right supports) they work fine bu I am printing new ones. If anyone wants one of the caps and a pin IM me your address and I’ll send one out.

[Novagunner]

Those upper receiver covers are pretty slick. Printed out a few and work great for most uppers. Need to mod one for the Max11/15 and do some for the M10.

[woodenword]

Anyone willing to sell a couple of these? I switch around between three different uppers so two would be great.