UZI Talk Forums
+ Reply to Thread
Results 1 to 3 of 3

Thread: Aging MP5: worn receiver rails, worn roller holders, side play of the bolt.

  1. #1
    Registered User
    Join Date
    Oct 2015
    Location
    Northern Virginia
    Posts
    505

    Aging MP5: worn receiver rails, worn roller holders, side play of the bolt.

    Hi all,

    Iím trying to get a better understanding of how an HK MP5 with a registered receiver ages. While I am not sure exactly, it sounds like similar to M60s, there are some issues than are difficult to fix.

    Like the AC556/FNC without spare parts, the M60 receivers that do not hold up well after a certain round count, how well does an MP5 age?

    When I think about firearms like the M16, where the firing movement is separated from the registered lower, I could envision M16s, Macs, Stens, Sterlings and other more simplistic firearms holding up better. I just donít know where the MP5 sits on the spectrum.

    Thanks!

  2. #2
    UZI Talk Life Member
    mattnh's Avatar
    Join Date
    Apr 2012
    Location
    NH
    Posts
    1,068
    With MP5, you will wear-out & break bolt parts, springs, buffers, & barrels.
    If you run the wrong locking pieces, rails will eventually get bulged.
    An Hk smith (or you) can fix anything that goes wrong
    and worse case refinish it. Barrels are a PITA to replace& likely
    Will result in a refinish. As long as you don’t kaboom the RR markings,
    I don’t see how you couldn’t have a brand new gun for 1.5-3k of work.

    WRT M60s wear (I own multiple of them)
    M60 bolts,Oprods,barrels, and recoil springs are consumables
    (figure hot swap them out yourself ~20k rds - With minimal care, you
    can avoid 90%+ of the wear issues).
    If you have a registered Channel M60, I’d basically consider it indestructible,
    a complete receiver rebuild to new is 3K.

    WRT repair costs

    Hk sear < dias< mac < 1919 < m16 < mp5 RR < m60
    Last edited by mattnh; 05-06-2022 at 09:25 PM.

  3. #3
    UZI Talk Life Member

    Join Date
    Mar 2006
    Location
    Southern New Hampshire
    Posts
    2,429
    In the HK MP5 Submachinegun book by Frank James, he stated that the Cape Canaveral security team had some MP5s that were specifically used for training. One in particular supposedly had over 500,000 rounds through it. The gun had had the barrel replaced three times with multiple bolt groups and rollers. The trunnion was so worn-out it needed replaced. To bring it back to spec, it would cost more rebuild than to buy new so the MP5 was removed from service and replaced. I think this was in the early 80s.

    The armorer at The Gun Store in Las Vegas showed me a Pre Sample MP5 with over 1.2 million rounds through it. It looked pretty rough. I think he said the trunnion had been replaced three times and the barrel had been replaced around 10 times. They use frangable ammo to eliminate the lead hazard which was very hard on the barrels.

    As far as longevity of any machinegun, Vegas machinegun rental would be the place to find out. Of course they are running a few mags and rotating customers. They are also shooting at short indoor ranges. The rounds could be keyholing. Accuracy is not that big of a deal in the rental business. Most anything can be repaired. Of course there is a huge difference between repairs for a Post Sample and a transferable.

    Scott

+ Reply to Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts


Please consider becoming an UZI Talk Supporter.