Search results

i would also check the chamber to make sure no burrs, grit, caked in carbon is making it harder for brass to come out of chamber, you might try reisizing some fired brass, hold gun barrel down insert one in chamber, with receiver plug and recoil spring removed, drop bolt into receiver, turn gun...

i thought the admin's opinion to begin with(before any bills were fleshed out) was suppressors are not firearms but accessories and should not be regulated at all by the fed gov in any form. this is just the first step(getting rid of the tax). next step no fed paperwork (paperwork(read database)...

I THINK THAT IS an old garth choate (Choate Machine & Tool) aftermarket flash hider from many years back.

https://www.titleiiarms.com/Uzi_Mini_Pistol_Semi_Striker_Assembly.html look at these by titleii he is the man

if you can find these each one can hold 8 suomi mags the ones i acquired had to be oiled up as the leather was quite dried out from their age https://www.libertytreecollectors.com/productcart/pc/viewPrd.asp?idproduct=6045

irvine, ca gun bought NIB in 1990 single owner bolt looks to be 1.125" receiver is broach cut I assume to let burnt powder and such debris as would accumulate escape receiver measures 1.150" at broaches measures 1.180" so broaches total is 0.030 or 0.015 depth at each broach gun was a "C"...

The early AWC Mk9 12" x 2" with baffle stack was early 90's when everybody wanted quiet irregardless of can size. all the mp5 & uzi guys doing full mags dumps with subsonic were happy. Later AWC changed to a K baffle stack in the inner tube which made a higher pitch which doesn't sound as nice...

hitecarms can make you an sd in mp5 or mp5k config i believe matt used to work for murray urbach and does excellent work

before i welded onto the endcap I would rather drill and tap with a substantial sized bolt thru a pic rail that would extend down maybe 3 to 3-1/2 inches and experiment with a preffered attachment height off the rail below tube level. if i wanted to swap later simply unbolt off the endcap to...

for the non-reloader try these--if you like them go back and get the 1000 package https://www.sgammo.com/product/9mm-luger-ammo/50-round-box-9mm-luger-147-grain-fmj-encapsulated-subsonic-winchester-ammo-zx

after may 19, 1986 several manufacturers were modifying receivers so sears and conversion parts would fit and run. eventually BATF decided these mods were "making a MG" those already done were permanently married and no new were allowed. relieving the trunion on a mini or micro receiver is not...

surprised you went with .355 others have being doing heavy 357 with 9mm cans theres a penn state 230 graindbl wad cutter "thunderhead' that can be set deep for pump guns (like IMI Timberwolf that will hold 9 +1) then theres the 200-250 grain 358 rifle bullets (jacketed) to play...

look under general references on front page of this website https://www.uzitalk.com/reference/pages/FAconversions_mini.htm

the Tom Denall Ruger 44mag Silent Destroyer has the factory barrel cut to 9". The inner tuber is then permanently affixed to the 9" original barrel and holds the baffle and spacer stack with slots in front of baffles for gas to enter the coaxial space. An escentric outer tube with a large...

here is another a little higher priced https://www.precisiondelta.com/products/9mm-147gr-fmj/

i have bought and loaded literally 1000's of these 147 grain round nose 9mm. https://www.rozedist.com/mm5/merchant.mvc?Screen=PROD&Store_Code=RZD&Product_Code=R152-A&Category_Code=ZBJ-9MM

if folks are receiving Micro barrels now maybe I will be seeing a couple soon--Yea!

i'll take 2.

(1) Micro 5.25" ported---9mm (1) Micro 4.5" Plain---9mm Email sent

read and download all the stuff on samachine.com about mags, lock-up (about a dime's thickness under the ejector) , and troubleshooting, also the MGN article Sept 1993 "Performance Surgery for the MK760" is good if you can find it. If mags can move forard or backward at lockup do not pull back...