Search results

Just a heads up...If you squeeze them in a vise like that make sure to check your feed lip width. Typically the lips will open up on most mags when squeezed on the front and back and will need to be pulled back in. Some mags are worse than others but when the feedlips open up all sorts of...

Hi USMG, unfortunately we dont have an ACE anywhere near us. Right now I am trying to fill out an order from ASMC and figured on throwing some into my total.....just need the sizes...... if anyone knows. USMG on a side note. been browsing through your site. I have not been messing with my...

They might be rushing production to make as many as possible as quickly as possible and getting a little sloppy. This happened in the assault weapons ban. QC went to hell for aftermarket mags because manufacturers were working 24/7 to get mags made before the bill went into effect. That...

Hello fellas. Hope everyone is doing well. I dont do much internet chat these days but I am kind of stumped. Anyone know the e clip size on the SWD/Cobray semi auto closed bolts? I did a search and couldnt find anything. Need to fill out an order for some set screws (other project) and...

I think the rods,and filled in witness holes were to make them more reliable in sandy environments.

They "can" work if you tweek them. They are just poorly constructed and dont last very long because the metal is thin and soft. My experience with these is in semi auto guns. The magazines themselves come from western/national magazines. I think in the long run your better of getting the...

Mega Mags, National, Western.......are all the same mag sold under different names. The steel is thin, springs not so great, and manufacturing is very sloppy and inconsistant. You can pick some up but be warned. They are some of the worst mags out there reguardless of what firearm the...

Armson are an old design but they were still being made last time I checked a few months ago. They are pretty popular for paintball. I would never shell out $400 for one but cobray stuff is collectable and the prices are all over the place.

most people who actually own them are happy from what I have read across the net. As far as the jamming goes...vulcan/velociti arms semi auto macs are known to have the barrels pakerized both inside and out. A little polising on the chamber and its good to go. I think they recommend steel...

Best way to get magazines clean from cosmoline/grease is to take them apart and boil them. Adding a little simple green helps quite a bit. Cosmo is great for storage if your never going to touch the gun but it realy stinks for anything else. I dont boil the springs though. The springs are...

It needs at least three more rails and a six point adjustable AR stock before I can drop 1200 on it. A bayonet mount would not hurt either.

Its neat I guess but if your going to go the SBR route there are better options. I would take a SBR mac10/11 over that and it would probable be cheaper. It reminds me of the mech-tech (spelling?) systems but with the hassle of SBR. In fact I think I would take a system with a 16" barrel where...

Might be worth it if you just need one or two. If your serious about having multiple mags for your baby mac cut the magwell off and put on a standard zytel type magwell and your optiuons open up considerably. Baby mac magazines are just not worth the headache. $100-$150 per magazine is crazy...

any chance you could measure the length of pull? It looks really long to me.

There are lots of Vulcans out there that run perfectly fine. Yes, there are also some that have issues but the same can be said for SWD/FMJ/Leinad as well. MPA problems are pretty rare.

Only if there is something wrong in a major fashion. Hammer has two hooks. There is a primary and a secondary. Assuming his gun was a closed bolt (and all vulcans are in my experience) the only way I see this happening is a stuck fireing pin or possibly a round with a potruding primer that...

Dont take it back. These guns are a cinch to work on. It looks like the raised portion of the hammer is leaving marks indicating that the portion of the hammer that contacts the fireing pin is not giving a full strike. I would try to flaten the striking face of the hammer and cleaning up the...

Most current promag stuff is pretty decent. I will say that if you are impatient and dont have the ability to tinker with magazines then dont mess with them. I dont have an UZI so I have no experience with that particular magazine. First thing to do would be to degrease it as many magazines...

Make sure the bolt is ok. Sometime the rear of the bolt around the fireing pin channel will deform and bind the fireing pin enough that you dont get a good strike. Unless your fireing pin is too short or defective you should not have to order a new fireing pin. If the rear of the pin channel...

in the realm of reality it would be a Beretta 93r. Outside of the the automatic grenade launchers we shot in MP school would be fun. I cant remember the model. M213 maybe. One of those 10mm rifles from Aliens would be nice.