Search results

  1. C

    Mag release

    If you're decent with a dremel tool, yes. I put and Odin extended mag release button on mine after watching this video: https://www.youtube.com/watch?v=mkq1QDcT4eU&t=8s
  2. C

    FNC Parts

    Just drill the hole out and thread it, I did mine to 10/32 and used a socket head set screw. This also allows you to regulate the gas system somewhat.
  3. C

    Rewoked ORF lower with complete FCG

    The story is that Franford was in the middle of trying to produce new FNC's when the engineer they had working on the project died. Unfortunately, the project died also and only a handful of toolroom samples were made. The serial number on the Gunbroker auction is 12, and it looks like there are...
  4. C

    WOW!!

    In 2027, yes. In 2017, no.
  5. C

    BOLT GUN ,STOVE PIPING NOT A EXTRACTER PROBELM

    First, put the bolt (without the recoil spring) in the receiver and check to see where the ejector is as it passes through the slot in the bolt. It should be as high as possible without dragging on the bolt, and riveted solidly so it doesn't move at all. If you need to adjust it, you can use a...
  6. C

    new high dollar mark for NIB Uzi?

    I'm going to try this one more time and then I swear I'm out. The guy did not bid against himself!!!! You can't bid against yourself. The first bidder put in a very high maximum bid and every time someone else bid against him, the offer was below the first bidder's max, so the autobid system...
  7. C

    new high dollar mark for NIB Uzi?

    Again, if another bidder enters a bid and it's less than the max of 17K, it will ONLY show the automatic greater bid of the guy that bid 17K. In fact, you can't bid against yourself. If I'm the high bidder and I keep entering higher max bids, the system won't make the bid higher until someone...
  8. C

    new high dollar mark for NIB Uzi?

    That's just the way the Gunbroker autobid system shows bid history. If I put in a maximum bid of 17K, the Gunbroker system will enter the smallest bid that will put me on top. When another bidder enters a bid (as long as it's less than the 17K max I entered), the system will enter another bid to...
  9. C

    Any interest in Swedish AK5 parts?

    I'd like one of these: New Bolt handle with oversized knob, $30 each. Paypal payment sent 9/14, thanks.
  10. C

    Anyone shorten your FNC Barrel?

    You can shorten the barrel to 14.5" and it should still function fine (mine did). At most, you may have to adjust the screw on the front of the gas block or turn the gas tube to the adverse setting. The problem is, it's not easy to pull the barrel from the receiver to put it in a lathe like an...
  11. C

    Updated my FNC to the Dutch trial rifle configuration

    I've been thinking of removing the grenade launching sight on mine as well. Did you have to use washers as spacers to make up the space, or did you just remove it and reassemble the parts without it?
  12. C

    Anyone ever get C&S Metall-Werkes to service or fix one of their old M11/9 drums?

    Several years ago I asked Ken why they stopped making and selling their drum mags. He told me that they were a pain in the butt to get running right and they were tired of screwing with them. That being said, I doubt that they're chompng at the bit to work on a used one.
  13. C

    Value of NIB Norinco

    $550 is a fair price for a NIB gun. The Norincos are built like tanks, probably the most robust AK's around with thicker than average receivers and excellent quality chrome lined barrels. And as a Chinese product, they can never again be imported into the US (at least not until they take us over).
  14. C

    223 AK mags....what's the story?

    Norinco metal .223 mags like the one shown in this link should be your first choice. I believe Bulgarian .223 plastic mags can be made to work also with some trimming. http://picturearchive.auctionarms.com/700171138/9542799/dscn6499-1.jpg_thumbnail1.jpg
  15. C

    7.62x25

    I don't think these will fit a sten magwell. They do fit in an M-10 magwell. That's the same person I bought my magazines from. If you look at his previous auctions on these, they usually go for more than what I'm asking.
  16. C

    7.62x25

    I was planning on doing a 7.62x25 caliber conversion and bought six CZ24/26 magazines. They are in very good to excellent condition and I'm looking to sell them for $110 shipped for the lot. Let me know if anybody want them.
  17. C

    Best .45 AR lower?

    I use a Cavalry Arms polymer lower with a Hahn .45 magwell adaptor, and it works well and is very lightweight. the Cav arms lowers are not currently being produced, but a number of dealers still have some in stock for around $100 plus shipping. This setup allows me to use unmodified greasegun...
  18. C

    7.62x25

    If you make up a few, I'm in for a 7.62x25 barrel for my M10 also.
  19. C

    what rpm bolt in a Max-11 ??

    The "tactical" 750rpm bolt is ideal in my opinion.
  20. C

    9mm single stack or double??

    You can't tell by looking at the outside. You have to see the bottom of the bolt. Double feed bolts have a squared off area about 3/8' wide on the bottom and single feed bolts taper to more of a V shape on the bottom.

Please Visit our Sister Sites Below

Sister Board - Sturmgewehr Sister Board - MachinegunBoards


Please consider becoming an UZI Talk Supporter
Top