Search results

The M11 and M10 are almost the same for disassembly etc.. .Except for the trigger spring is very different between the two.

Michael will give you a call Monday.

I have sent them an email on Saturday with no response yet. They also have an account on the forums here but haven't logged in since 1 July 2017. I'm just trying to get some opinions of those that may not be green to answer if it is or not compatible.

This Upper: http://www.usmachinegun.com/proddetail.php?prod=M10U-0104 This Bolt: http://www.usmachinegun.com/proddetail.php?prod=M10SMG-0107 I ordered them a few months ago but wasn't able to get out to the range until this past weekend. It didn't function at all. So I'm just making sure that...

I have a SBR with an Adams Arms 7.5" Upper. The gun is very accurate, at 50 yards standing I can hit clay pigeons very easily. Off a bench would hit them all day long.

if you have a LAGE upper with the side rails installed you can use the AR15/M16 brass catcher from Tactical Brass Recovery. http://www.tacticalbrassrecovery.com/ar15-ar10-platform-brass-recovery-bag-standard-issue/

That picture there makes it clear this may not be truly NIB. I don't believe Flat Top M16/AR15 uppers were made prior to 1990.....???

Does your 10.5" upper seem to run under gassed with it? I put together an upper, using the 10.3" DD barrel and Adams Arms Piston system using the Flash Enhancer and seemed that it was under gassed ejecting the spent cases to the 4-5 O'clock positions. I was also using wolf ammo which could be...

I just received some un-modified GG 45ACP mags they seem to fit correctly, will try them out on Saturday.

so I will ask again, can these only be used with the M11?

I bet you Frankford Arsenal is the one that did the conversion on an Olympic Arms Receiver. My Form 4 doesn't even mention PAWS but that's who actually made it into a MG.

Edit: to clarify that there are NO factory OA Transferable M16's Just putting this out there that all Olympic Arms based M16's were converted, there are No Factory Transferable M16's. I have a PAWS OA M16, non-mil-spec uppers will not fit my lower, Usually if the upper will not fit my M16...

Can these be used on the M10/9mm set up? Are they for single feed bolts only?

I got my PS M10/45 last year and I have been using it with a LAGE Mk2 9mm upper with a Double Feed bolt. I've had feeding issues with it which I posted an another thread, trying to use "factory" and converted Suomi mags Also since I first got it, I upgraded the grip to the LAGE Grip with Thumb...

I think the bolt is touching/bumping those guides on my feed ramp when it comes back to the rear. I now have two magazine well converters for 9mm, I might as well tweak the feed lips on the one and flatten those guides and trim the width and see what happens with that. Ordered some 9mm snap...

LawBob I don't think that is 100% true about the guides on the feed ramp are necessary for the double feed type magazines. If you look at MPA guy's M10 9mm using double feed mags his feed ramp has no guides and from what I have heard from him his runs very well. I haven't started reloading yet...

Okay, well had the chance to get to the range today. I bent the feed ramp so it was squared. Still same problems. Also it didn't matter if it was the right or left side it would malfunction. The tip of the round was off to the side like I described before. Now I'm wondering if it is the feed...

aww didn't think to use some kind of thread lock. I just looked up and found this: Flexbar Rocksett High Temperature Thread Locking Compound 2 oz Anyone have experience with it?

bumping because I edited my post last night. Do stripped uppers normally come with the barrel retaining pin hole not drilled in them? As far as I can tell the barrel hole is threaded.

which size drill bit should I use? It all depends when I get the parts in when I will actually be able to do it. so that's why I'm gathering information now. Thanks Edit to add: Looked at the upper when I got home tonight, there is no hole in the upper, what to do??