Search results

Wes- Although these are slightly different when I had an Uzi doing 3gun matches, I used this style, starting out on a H harness, then later used them on a plate carrier. Now using them with my Colt 9mm carbine. Never had any issue with them...

Heh, that’s because I didn’t Answer my own question. You posted some very good information, but If you reread the posts, I was using SOME REM 115, along with Super Vel 100 for testing, along with all of his various 124gr. FMJ factory loads, brass & steel case. All of these EXCEPT the Super Vel...

They are just fine. Very flat shooting and accurate In both his Vector Uzi and my Colt 9mm AR carbine. They are loaded specifically for 16” barrels. I don't use them in my pistols (I also use 124, as well as 147 in pistols). Here is the link if interested...

Naw, good question, but I have a good grip and shoulder it properly. I use to have my own IWI Uzi (B) model for 20 years that I used in 3 gun matches and other than a bad mag & a couple of duds, bad primers in ammo, never had any mechanical issues with that one. This is a late production Vector...

FN, South Africa, IMI & German. The German ones were unissued, still full of cosmo in plastic wrap (cleaned them of course). It doesn’t seem to matter mag wise, as they all have the same issue. I really think it’s ammo picky, since the 100gr. rounds worked 100% in all of them.

Western part of the State. Yes, please do.

So finally had some time and did the following: I tried Jones suggestion (thanks again) on putting fired cases on the bolt face and sliding the barrel back in. Had no resistance on any of the cases I tried. Used mostly his ammo cases (steel cased LVE), as well as several other brands / brass &...

Jones: That’s something I haven’t tried. Will give it a go. Thanks!

No. Don’t have a spare.

Heh, tried different mags first thing. Think we’re up to 8 now. Made no difference.

Thanks all for the advice. As to ammo, he is using various 124gr. FMJ factory loads, brass & steel case, As ‘read somewhere’ to use 124. They all have the same issue. I put a couple of mags worth of my Rem 115gr and Super Vel reload 100gr. Blitz ammo. Same issue with the 115, but no issues...

So I have a family member who has a Vector arms full size mod.A Uzi carbine. Probably has 500 rd.s through it (bought it new). He is having occasional issues of getting a round not fully feeding and getting hung up. I stripped it down, cleaned it and did notice that the ramp seemed a tad rough...

Primary Arms 2.5x scope on a semi carbine. I like being able to hit the 200yd. Half silhouette gong on a regular basis.

I normally use a Primary arms SLX 2.5x32 prism scope on a StormWerkz rail for my full size Uzi carbine. No issues regularly hitting a full size silhouette at 200 yd.s. with 115 gr ammo.

So received it, it’s very well made, but no, it wasn’t flush. About half an inch of barrel sticking out. They never responded to my email inquiry, but that’s not uncommon these days with many small shops. Guess I’ll thread the barrel and put a light weight flash hider on it.

Thanks-kanewtervalve

Wow, no one? Okaaay. Guess I’ll order one and hope it fits.

For those of you that have a full length 16” barrel Uzi carbine that has a US barrel shroud, is the barrel muzzle even or just below the shroud? https://shop.usbarrelshrouds.com/Uzi-Vented-Barrel-Shroud-_p_24.html Thanks!

Thanks for the info gents. 100M it is.

Well I did find this thread on AR15.com regarding zeroing a 9mm carbine. https://www.ar15.com/forums/armory/-/48-326442/? Zeroing a 9mm AR Carbine by LTC Chuck Santose 115gr 9mm Parabellum. Recommend you zero at 25 yards. With this zero the bullet is no more than an inch from line of...